Understanding Whisky Production Unit 3: Raw Materials Processing

Chapter 6: Milling and Mashing: Grist Proportions and Starch Conversion

Roller mills, plansifters, the classic 70/20/10 grist ratio, and how alpha- and beta-amylase convert starch into fermentable sugars in the mash tun.

On this page

Once malt arrives at the distillery, it must be crushed into grist. This sounds straightforward until one considers that grinding it too fine creates an impermeable paste resembling library wallpaper paste, while leaving it too coarse means hot water cannot reach the starch inside.

The time-tested compromise is the classic ratio: roughly seventy percent grits, twenty percent husks, and ten percent fine flour (Crisp Malt’s distilling mash protocol; Difford’s Guide). The husks form a porous, natural filter bed at the bottom of the mash tun, allowing warm water to percolate through. At a mash temperature of around 63.5°C to 64°C (Crisp Malt’s distilling mash protocol), two key enzymes awaken: alpha-amylase chops long starch coils into manageable segments, and beta-amylase snips off sweet pairs of glucose molecules to create fermentable maltose.

Grain Intake and Storage

During delivery, the CoA (certificate of analysis) and visual checks will determine whether the grain is to be offloaded or rejected (Step 1 in the high-level flow diagram below).

Grain intake: checks before storageGrain intake: checks before storage. Schematic • not to scale. Delivery and certificate of analysis; Visual inspection; Accept only conforming grain; Offload with dust extraction; Remove stones and metal; Clean, dry storageUNDERSTANDING WHISKY PRODUCTIONGrain intake: checks before storageDelivery and certificate of analysisVisual inspectionAccept only conforming grainOffload with dust extractionRemove stones and metalClean, dry storageUisge BeathaSchematic • not to scale
Grain intake: checks before storage

You need to check for the following before accepting the batch:

Once you are happy with the quality of your grain, you are now ready for the intake (Step 2 in the high-level flow diagram). You must always keep health and safety requirements and considerations in mind. Large plants that offload into silos, will have grain elevators, magnets, combi-cleaners (classifying screens with an additional dust extraction section) and dust extraction. Smaller plants must have dust extraction and magnets, as a minimum, to reduce the risks of human exposure to dust and dust explosions. Operator interaction with dust can lead to occupational asthma, rhinitis, conjunctivitis or other ailments (HSE guidance on grain dust also lists chronic bronchitis, farmer’s lung and grain fever among the risks). Long term exposure to dust should be managed by decreasing exposure and using personal protective equipment (PPE) such as filter face masks if interaction is a requirement.

The general rule is that where any grain is moving and producing dust, dust extraction must be in place. The risk of a dust explosion is always present: under the Dangerous Substances and Explosive Atmospheres Regulations, workplaces handling explosible dusts such as flour must be assessed and protected (HSE guidance on dust explosions in the food industry). One way to minimise the risk is to use good housekeeping, e.g. keeping the area free of dust, pests and ignition sources.

The five factors in a dust explosionThe five factors in a dust explosion. Schematic • not to scale. Fuel; Oxygen; Ignition source; Confinement; Dust cloud; Dust explosionUNDERSTANDING WHISKY PRODUCTIONThe five factors in a dust explosionFuelOxygenIgnition sourceConfinementDust cloudDust explosionUisge BeathaSchematic • not to scale
The five factors in a dust explosion

Removing foreign material from the grain during intake into the storage units is good practice. We can also remove it just before the grains go through milling. Equipment such as de-stoners remove stones (possible ignition sources), which are a similar size to the grain. Combi-cleaners are common in distilleries for removing coarse (e.g. broken kernels), fine (dust), stones (usually larger than the grain), and low-density material (loose husks). Magnets, either permanent or electromagnets, are vital for removing metal particles during intake. They are also used before the mill to remove possible ignition sources. Another way to reduce the risk is to electrically bond and earth all the equipment (HSE recommends both magnets and earthing in the same guidance).

If you remove just one factor, the dust explosion cannot occur.

Grain Storage

Until you are ready to use the grain you must ensure it is stored safely. Stocks of grain at a distillery will be kept to a minimum level to save costs and manage the businesses cash flow. Grain that is stored must be kept dry and free from infestation of any kind e.g. rodents and insects until it is ready to be used. Grain is often stored in silos and these must be free from leaks, clean and ideally self-emptying. Grain can also be stored in bags. These bags must also be kept in conditions that are dry and free from infestation.

Calculation of Grain Quantity Required

One of the most important things for a distiller to know is how much grain they will need in order to produce a given quantity of wort, at the desired strength. Wort collection is discussed in more detail later and in further chapters, but you need to understand how it is measured because it is an input for this calculation.

Distillers and brewers measure wort strength in a variety of ways. Here, we will refer to the Specific Gravity (S.G.) measurement a standard measurement in distilling. Specific gravity is a way of showing the density of a substance in relation to a reference substance, typically water. Confused? That’s ok. Let us break things down a bit.

We know that density is defined as a substance’s mass divided by its volume. Essentially, density tells us how much mass of a substance fills a specific amount of volume. We also know that water has a density of 1.000 g/mL at 4°C., which means that one mL of water weighs one gram. Something denser than water would have a higher weight per one mL. Specific gravity is simply showing the ratio of that substance in relation to water. So back to our wort.

If our wort has a density of 1.060 g/mL, and water has a density of 1.000 g/mL, we then know that the specific gravity of our wort is equal to 1.060 g/mL divided by 1.000 g/mL, which is simply 1.060. Notice that the units cancel out in the equation, so specific gravity is a unitless quantity. (The actual definition of specific gravity is much more complicated than this. However, as distillers, we do not often need to worry about that.)

Brewers and distillers often multiply specific gravity by 1,000 and then subtract 1,000. Unbelievably, this actually makes talking about gravity far simpler. For example, if our specific gravity were 1.060, we would multiply that by 1,000, which gives us 1,060. Subtract 1,000 from 1,060, and we are left with 60. This is often referred to as excess gravity, and 1,060 would mean that there are 60 points of excess gravity. See? Not that hard.

OK. Back to calculating our grist weight. In order to calculate the amount of grain needed for a batch of whisky, we need to know three things:

  1. The desired excess gravity of the wort we are trying to create
  2. The volume of wort that we need
  3. The amount of soluble extract that our grain contains

As distillers, we decide the wort gravity, so there is no problem here. We also decide the volume of the wort. The only thing we have to look up is the soluble extract value for our grain, which the cereals chapter covers, is not too hard to find.

The equation for our grist weight looks like this:

Grist weight (kg) = (volume of wort in litres x excess gravity) / (soluble extract % x 3.87)

where excess gravity is the specific gravity points above 1.000 (so 60 for a 1.060 wort), and 3.87 converts the soluble extract percentage into litre-degrees per kilogram of grist.

This is a simple plug-in calculation. Do not worry about 3.87: it is a simple factor to make sure that everything comes out correctly. So, let us try this equation with our 1.060 specific gravity wort. We will assume that we want 10,000 litres of volume, and that our barley has a soluble extract of 77.5%.

Grist weight = (10,000 x 60) / (77.5 x 3.87) = 600,000 / 299.9, or about 2,000 kg of grist.

As a cross-check, Crisp Malt’s distilling mash protocol makes 5,000 litres of wash at 1060 original gravity from 1,000 kg of malt with a soluble extract above 78%: the same ratio of about 200 kg of malt per 1,000 litres.

Pretty simple, yes?

Milling Process Overview

The purpose of milling is to expose the starch. Milling gently detaches the tough fibrous husk from the starchy endosperm, whilst also reducing the particle size of the starchy interior.

In Scottish malt distilling, you feed the now thoroughly betrayed barley through an ancient roller mill, typically a Porteus or a Boby: names that sound equally like heavy industrial machinery and minor characters from a Victorian novel. If a distillery does not already possess one, it generally raids a derelict brewery, which tend to collect them the way galaxies collect dust. The Porteus mill in particular has a reputation for such indestructible cast-iron durability that, as the distillery-tour story goes, the manufacturer ran out of customers. The firm, George Porteus and Sons of Leeds, made brewing and malting plant and was taken over by Dawson and Barfos in 1966 (Grace’s Guide).

Milling increases the surface area of the starch granules available, which assists in the conversion processes that take place during mashing. Various mill types are available today; we will now investigate the most common designs and consider how they manage to separate the husk from the starchy endosperm.

Milling Technology - Two-roller Mill

How a two-roller mill crushes maltHow a two-roller mill crushes malt Malted grain; Crushed grist leaves the gap; Fluted rollers; The gap controls how finely the grain is crushed.UNDERSTANDING WHISKY PRODUCTIONHow a two-roller mill crushes maltMalted grainCrushed grist leaves the gapFluted rollersThe gap controls how finely the grain is crushed.Uisge Beatha
How a two-roller mill crushes malt

The most basic mill is the two-roller mill. It is also known as a grist or agricultural feed mill. The name gives you a clue about its operation. It uses two rollers to crush the grain. The operation of a two-roller mill is the basis of the design for other dry mills with multiple rollers. The figure above shows that the rollers turn in opposite directions, allowing the flutes (grooves) on the rollers to grip the kernels. The area between the rollers crushing the grain is known as the mill gap. It is important that we align the feed of the grain with the middle of the rollers, to ensure that the rollers grip and crush the grain. Mill gap optimisation is important in order to produce correctly sized particles. The crushed grain (grist) coming out of the mill rollers consists of flour, grits and husk.

Grist - A term used for milled grains that are ready for use in mashing. Grits - A term used to describe a crushed grain endosperm particle after milling.

The grist composition will differ depending on the type of mill you use. Two-roller mills do not give you any real flexibility, other than changing the mill gap setting to control grits size distribution. By flexibility we mean the types of grains that can easily be crushed. Some unmalted grains such as wheat and rye benefit from having several sets of rollers that have progressively tighter gaps between them. This allows for much better particle size control. Let’s take a moment to look at these types of mills in more detail.

Those distilleries that use two-roller mills do so due to the higher capital cost of four- or six-roller mills.

Milling Technology - Four-roller and Six-roller Mills

In addition to the two-roller mill, there are two other commonly used roller mills; the four-roller and six-roller.

Four-roller Mills

The figure below shows a typical four-roller mill. The first rollers will detach the husk from the endosperm. The husk and flour are separated, sending the coarse grits through another set of rollers to reduce their size. A four-roller mill is suitable for well-modified malts, since the starchy endosperm is accessible with no residual β-glucan cell walls after the completion of malting. The distiller easily controls the particle size, and the grist composition is made up of grits, flour and husk.

Four-roller millFour-roller mill. Schematic • not to scale. Grain inlet; Rollers; Milled grist; Successive gaps reduce the grist size.UNDERSTANDING WHISKY PRODUCTIONFour-roller millGrain inletRollersMilled gristSuccessive gaps reduce the grist size.Uisge BeathaSchematic • not to scale
Four-roller mill

Six-roller mills

Milling less modified malt typically requires a six-roller mill. The function of a six-roller mill is similar to that of a four-roller mill. It just has an additional pair of rollers and sieves to give even more control over particle size.

Six-roller millSix-roller mill Grain inlet; Rollers; Milled grist; Successive gaps reduce the grist size.UNDERSTANDING WHISKY PRODUCTIONSix-roller millGrain inletRollersMilled gristSuccessive gaps reduce the grist size.Uisge Beatha
Six-roller mill

Milling Technology - Hammer Mills

Roller mills are not suitable for distilleries using green malt and other unmalted or undermodified grains. Enter the hammer mill.

Hammer mill: impact and screeningHammer mill: impact and screening. Schematic • not to scale. Grain inlet; Screen controls particle sizeUNDERSTANDING WHISKY PRODUCTIONHammer mill: impact and screeningGrain inletScreen controls particle sizeUisge BeathaSchematic • not to scale
Hammer mill: impact and screening

The figure of the hammer mill above shows the free-swinging metal hammers attached to a rotor. The hammers crush the grain into smaller pieces, and the sieve separates the required smaller-sized particles from the larger pieces. The hammer mill operation is similar to that of the friabilimeter, which measures how well and how easily the malt crushes. However, in the friabilimeter, the grain is crushed against the sieve, whereas in the hammer mill, the hammers crush the grain.

Grist Analysis

It is essential to analyse the grist after milling, to ensure that both the composition percentages and the actual size of the crushed starchy endosperm (grist), are acceptable (husk, coarse grits, fine grits, flour). We must visually inspect the grist as frequently as possible, especially if there is a raw material change, such as a new batch.

Grading sieves (plansifter) give an accurate analysis of the different fractions of the grist particle size distribution. Sieves with various sized holes separate the different particles in the grist. Depending on the method, the number of sieves can vary. However, the EBC (European Brewery Convention; the technical group in Europe that among other things decides the testing parameters and standards for brewing ingredients, and by default distilling ingredients) method typically uses a set of five Pfungstadt plansifter sieves, with a pan at the bottom for flour, and a lid (First Key Consulting, citing Briggs and co-authors). You can manually shake the sieve; however, you will obtain results that are more accurate by using an automated shaker with a timer. Using this method would provide the grist with the same motion and time duration, and achieve the same results.

Grading grist with sievesGrading grist with sieves. Schematic • not to scale. Largest mesh; Fine flour collects in the panUNDERSTANDING WHISKY PRODUCTIONGrading grist with sievesLargest meshFine flour collects in the panUisge BeathaSchematic • not to scale
Grading grist with sieves

Visually, a sample should have big pieces of husk, small pieces of crushed endosperm, and some flour. The table below shows one example of grist analysis using the EBC method; actual proportions vary by mill and grist specification, and the classic 70/20/10 ratio is a rule-of-thumb target rather than a measured distribution. Roller mills preserve more husk than a hammer mill. A roller mill produces larger particle sizes than you would get from the same fraction taken from a hammer mill.

Scroll sideways to see all columns.

Particle size (µm)Screen mesh size (mm)Grist fractionRoller mill grist (%)Hammer mill grist (%)
Sieve 1> 1,2701.27Husk181
Sieve 21,010 to 1,2701.01Coarse grits74
Sieve 3547 to 1,0100.547Fine grits 13515
Sieve 4253 to 5470.253Fine grits 22020
Sieve 5152 to 2530.152Flour830
Pan< 152Fine flour1230

The figure below shows the visual distribution of the particle sizes. We will compare how these fractions influence the type of vessels that you will use during the process.

Grist fractions: roller and hammer millsGrist fractions: roller and hammer mills. Source example • roller / hammer percentages. Roller mill; Hammer mill; Sieve 1; 18%; 1.1%; Sieve 2; 2.7%; 2.4%; Sieve 3; 35%; 15%; Sieve 4; 20%; 20%; Sieve 5; 8%; 30%; Pan; 12%; 30%; Values printed in the source example, shown without; normalising.UNDERSTANDING WHISKY PRODUCTIONGrist fractions: roller and hammer millsRoller millHammer millSieve 118%1.1%Sieve 22.7%2.4%Sieve 335%15%Sieve 420%20%Sieve 58%30%Pan12%30%Values printed in the source example, shown withoutnormalising.Uisge BeathaSource example • roller / hammer percentages
Grist sieve fractions: percentages printed in the source example, without normalising the totals.

Figure: Visual illustration of EBC plansifter grist fractions

Effective distilling operations require regular assessment of the grist composition.

Before we learn how the grist composition affects the process, we need to look at the high-level wort production process used in distilling.

Wort production from barleyWort production from barley. Schematic • not to scale. Grain intake and storage; Steeping and germination; Kilning; Milling; Mashing: grist and water; Wort ready for fermentationUNDERSTANDING WHISKY PRODUCTIONWort production from barleyGrain intake and storageSteeping and germinationKilningMillingMashing: grist and waterWort ready for fermentationUisge BeathaSchematic • not to scale
Wort production from barley

After milling, the next step in the process is mixing the grist with water, known as mashing (as shown above). Milling directly affects the efficiency of mashing and the amount of sugars produced.

The liquid produced during mashing is known as wort. All the solid material that could not dissolve in the water is known as draff.

Mashing Process and Technology

The mashing process will differ depending on the raw material used. In this section, we will explore how to mash with malted grains, or grains with similar characteristics to malted barley. We will also identify the necessary technology required.

The purpose of mashing is to extract (dissolve) all the starch from the malt and convert the starch to fermentable sugars.

At this point in the process we have milled the grains to expose the starchy endosperm. Next, this grist needs to go into a mashing vessel. This vessel requires water to allow the starch to go into suspension. A basic mashing system contains the following components that enable this:

How wort leaves a mash tunHow wort leaves a mash tun Grist + water; Sparge water; Wort out; Draff out; False bottom; Grain filter bed; Liquid drains through the bed and perforated; floor.UNDERSTANDING WHISKY PRODUCTIONHow wort leaves a mash tunGrist + waterSparge waterWort outDraff outFalse bottomGrain filter bedLiquid drains through the bed and perforatedfloor.Uisge Beatha
How wort leaves a mash tun

The first step in the mashing process involves mixing the milled grain with the temperature-controlled water. The amount of water added will determine the mash consistency, also known as the liquor to grist ratio. A high liquor to grist ratio indicates that a large amount of water is part of the mash, producing a thinner mash compared to a low liquor to grist ratio. In Crisp Malt’s distilling mash protocol, the first water is about 4 litres per kg of grist and the second water about 2 litres per kg. The liquor to grist ratio is also important when it comes to preserving malt enzymes. High heat can denature enzymes making them lose their activity and subsequently causing a thicker mash. A lower liquor to grist ratio will heat up more evenly, and better protects the enzymes.

It is vital to effectively mix the grain and water. Manual mixing, or the use of screws or static mixers (Steeles Masher or grist hydrator) in automated plants, ensures that each of the starchy endosperm grits is in contact with the water. Hydration is vital in order to prepare the starch granules for the conversion process. The dry grits of starch are not yet fully accessible for breakdown by α- and β-amylase (enzymes covered in the malting chapter). What is the process that starch needs to undergo, in order to be ready for conversion? We will find out in the next section.

The Three-Water Extraction Regimen

In malt whisky production, distillers can use successive water additions to recover sugars from the mash. The stronger early worts go forward to fermentation; weaker later runnings may be retained for a subsequent mash. Temperatures, quantities and equipment vary between distilleries.

Published examples give a sense of the range. Crisp Malt’s distilling mash protocol uses a second water at 75°C and a third water at 90°C, which is returned to a weak-worts tank, kept above 70°C and used as the first water of the next mash. Difford’s Guide describes a second water of perhaps 75°C, a third around 85°C and a fourth around 95°C, with the third and fourth waters kept for the next mash; the Scotch Malt Whisky Society gives a second water around 80°C and a third around 85°C. These are examples, not a universal recipe for every distillery.

A distillery example shows why the temperatures should not be treated as fixed: Glasgow Distillery describes three water additions, rising from 70°C to 80°C and a final 85°C.

For broader discussion of Scotch whisky mashing and malt processing, see Bringhurst and Brosnan (2014), “Scotch whisky: raw material selection and processing” (doi:10.1016/B978-0-12-401735-1.00006-4), Bathgate (2016), “A review of malting and malt processing for whisky distillation”, Journal of the Institute of Brewing, 122(2), 197 to 211 (doi:10.1002/jib.332), and Bathgate (2019), “The influence of malt and wort processing on spirit character: the lost styles of Scotch malt whisky”, Journal of the Institute of Brewing, 125(2), 200 to 213 (doi:10.1002/jib.556).

Mash Conversion Biochemistry

During mash conversion, the starch transforms to promote the production of sugars. This transformation is known as gelatinisation. Once gelatinisation occurs, the next steps of starch conversion can happen; liquefaction and saccharification.

We know that starch consists of long glucose chains.

Starch: glucose chains and branchesStarch: glucose chains and branches. Schematic • not to scale. Amylose: an unbranched chain; Amylopectin: a branched chain; Each dot represents a glucose unit.UNDERSTANDING WHISKY PRODUCTIONStarch: glucose chains and branchesAmylose: an unbranched chainAmylopectin: a branched chainEach dot represents a glucose unit.Uisge BeathaSchematic • not to scale
Starch: glucose chains and branches

The bonds between the glucose molecules are not all the same, and this leads to differences in the structure of the long chain. The two important types of starch chains are amylose, which in most starches makes up less than 35%, and amylopectin, which makes up the rest of the starch granules (Laus et al. 2025).

Let us take a couple of steps back and start at the beginning of the biochemical process.

After milling, the crushed starchy endosperm contains starch granules and residual protein matrix. The starch granules themselves are roundish structures, with alternate layers of amylose and amylopectin. The granules differ in size. The large granules are known as Type A (about 10 to 40 μm across) and the small granules as Type B (about 1 to 10 μm). By number, about 10 to 20% of the granules are Type A and 80 to 90% Type B, but the large granules make up 90 to 95% of the starch by mass (Laus et al. 2025). The figure below shows the different types of starch granules. The granules appear compact and require more steps in order to enable conversion to fermentable sugars.

Barley starch granulesBarley starch granules Mixed barley starch; Large A-type granules; Small B-type granulesUNDERSTANDING WHISKY PRODUCTIONBarley starch granulesMixed barley starchLarge A-type granulesSmall B-type granulesUisge Beatha
Barley starch granules. Drawn schematics, not microscope photographs; not to scale.

Both amylose and amylopectin are present in starch granules, but they have a closed and compact structure, such as that shown in the first image in the figure above. This configuration does not support conversion of starch to sugars, since large parts of the chains are not in contact with the water. Only α-amylase can convert the starch granules, but at a very slow rate - much too slow for distilling. To open up the structure, we must firstly achieve a specific temperature, known as the gelatinisation temperature. This is determined by the grain variety and malting conditions. The table below shows typical gelatinisation temperature ranges for different grains, as given by the American Society of Baking. Published figures vary with the measuring method: Laus and co-authors, for example, report onset temperatures of about 59.6°C for barley A-type granules and 62.8°C for B-type granules (Laus et al. 2025).

Scroll sideways to see all columns.

SourceGelatinisation temperature (°C)
Barley51 to 60
Wheat51 to 60
Maize62 to 72
Rice68 to 78
Sorghum68 to 78
Rye51 to 60

The shapes of the starch granules also differ between the grains. The scanning electron microscope images below show the differences in wheat, barley and rice granule shape. Wheat and barley have similarly round granules, whereas rice granules have a polygonal shape.

Starch granules from different cerealsStarch granules from different cereals Ragi; Rice; Wheat; MaizeUNDERSTANDING WHISKY PRODUCTIONStarch granules from different cerealsRagiRiceWheatMaizeUisge Beatha
Starch granules from different cereals. Drawn schematics, not microscope photographs; not to scale.

Once the gelatinisation temperature has been reached, the process known as gelatinisation will occur.

Gelatinisation - This is a vital stage in mashing. The term refers to the process by which the tightly bound starch molecules unwind due to the action of heat and water. Gelatinisation allows them to dissolve. Enzymatic activity then breaks them down.

The figure below shows the amylose and amylopectin chains, now free to be broken down by α- and β-amylase.

Gelatinisation opens starch for enzymesGelatinisation opens starch for enzymes Granule; Starch packed; inside.; Swelling; Water and heat; disrupt the; structure.; Opened structure; Chains become more; accessible to; enzymes.; Gelatinisation changes starch structure; enzymes then; break bonds.UNDERSTANDING WHISKY PRODUCTIONGelatinisation opens starch for enzymesGranuleStarch packedinside.SwellingWater and heatdisrupt thestructure.Opened structureChains become moreaccessible toenzymes.Gelatinisation changes starch structure; enzymes thenbreak bonds.Uisge Beatha
Gelatinisation opens starch for enzymes

Once the starch structure unwinds, water can enter deeper into the starch polymers. This process is known as liquefaction. Water acts as the medium that will facilitate all the critical enzymatic reactions during conversion.

Achieving the gelatinisation temperature of the grain’s starch granules allows for complete hydration (liquefaction), and then the conversion of starch to sugars.

Saccharification is the process in which enzymes break starch down to sugars. It occurs after the complete hydration of the starch granules, which exposes the amylose and amylopectin chains.

Saccharification is the biological hydrolysis of biomolecules such as starch. Hydrolysis - from the Ancient Greek word hydro . Hydro means water. Lysis means ’to unbind’. The saccharification process in mashing uses the various enzymes to unbind the sugar molecules from the amylose and amylopectin chains.

The diastatic enzymes (starch degrading enzymes), α- and β-amylase are critical for the conversion process, but they will not be useful if the starch granules have not gone through the gelatinisation process, or if they have experienced suboptimal processing conditions. All enzymes have optimal ranges in which they perform best. Parameters such as temperature, time and pH, however, will influence the performance of the different enzymes.

Mash Conversion Enzymes

PH, temperature and time all affect the activity of enzymes such as barley α- and β-amylase.

Barley malt α-amylase works best at pH 5.6 to 5.8 and about 63°C to 74°C. β-Amylase works best at pH 5.4 to 5.6 and about 55°C to 65°C (Laus et al. 2025). Enzyme activity decreases outside these ranges. This is why it is important to find the best temperature, typically 62°C to 65°C, and the ideal pH for mashing to ensure that both α- and β-amylase are optimally breaking down the starch chains. There is an optimal time for the enzymes within their stated ranges, which will ensure complete conversion. Crisp Malt’s distilling mash protocol rests the mash for up to an hour, and notes that some Scottish distilleries run off much sooner because conversion continues in the fermenter.

Scroll sideways to see all columns.

EnzymepHTemperature (°C)Deactivation temperature (°C)
α-amylase5.6 to 5.863 to 74above 80
β-amylase5.4 to 5.655 to 6574
Limit dextrinase5.1about 65above 74

We need to look at the specific actions of the two enzymes, in order to understand how they will affect the wort. The figure below shows where α- and β-amylase will attack the starch chain, be it amylose or amylopectin. The figure represents a fragment of amylopectin, showing the branched section:

How enzymes break down starchHow enzymes break down starch α-amylase: within a chain; Cuts internal bonds, making shorter chains.; β-amylase: from a chain end; Releases maltose, a pair of glucose units.; Limit dextrinase: at a branch; Cuts the branch bond, opening access for amylases.; Each dot is a glucose unit; amber marks a cut.; Selected actions shown. Enzyme activity depends on mash; conditions.UNDERSTANDING WHISKY PRODUCTIONHow enzymes break down starchα-amylase: within a chainCuts internal bonds, making shorter chains.β-amylase: from a chain endReleases maltose, a pair of glucose units.Limit dextrinase: at a branchCuts the branch bond, opening access for amylases.Each dot is a glucose unit; amber marks a cut.Selected actions shown. Enzyme activity depends on mashconditions.Uisge Beatha
How enzymes break down starch

Did you know? The products from the diastatic enzymes are: Glucose - One glucose molecule. Maltose - Two glucose molecules in a chain. Maltotriose - Three glucose molecules in a chain. Dextrin - These are carbohydrates that have not been completely converted to fermentable sugars by amylases often due the presence of α-(1,6) branch points.

Malted barley contains two additional enzymes that break down starch. They are limit dextrinase and α-glucosidase (maltase).

Maltase has a low level of activity, but with enough time, it can break down the starch into glucose (as shown in the figure above).

Limit dextrinase will break the starch chain at the branching point, producing two new linear starch chains that can be broken down to fermentable sugars.

Limit dextrinase:

All enzymes are heat sensitive and are mostly inactivated towards the end of mashing. All the above-mentioned enzymes play a role in converting starch to fermentable sugars during the mash conversion process.

In brewing, the starch is converted in the mash tun before wort collection is started. The mashing-in temperature is typically 62°C to 65°C (a β-amylase rest), rising to a 70°C to 75°C saccharification rest before run-off (Laus et al. 2025). This reduces viscosity, but limit dextrinase will not have worked, and will have been denatured. The limit dextrins will not be broken down and in fact are important to give “body” to beer. This is not a key consideration for distillers.

In distilling, run-off (wort collection) commences as soon as possible, usually after a short recirculation (note, not all distilleries want a clear wort). Mashing at about 65°C or below, with no wort boil, lets limit dextrinase survive into the washback (Bringhurst 2015, Journal of the Institute of Brewing, 121, 1 to 18). Dextrin breakdown ensures maximum extraction of sugars, and hence higher Lpa/t.

Various factors that will influence enzyme efficiency include: • Temperature We have learned that each enzyme has an optimal temperature range. Any temperature outside of this range will reduce the enzyme’s effectiveness. • pH Similar to temperature, pH values outside of the optimal range will negatively affect the enzyme’s performance. • Liquor to grist ratio Thicker mash that has a lower water to grist ratio will protect the heat-sensitive enzymes better than a thin mash. • Time Additional time will not give you more extract, but it can give you more fermentable sugars. This, however, is only true if the temperature is adjusted to match the required enzymes’ optimal conditions.

The mash conversion process described thus far applies to grains such as barley, wheat or rye, whose starches gelatinise below normal mashing temperatures (American Society of Baking). They can be milled and mashed without additional steps. However, what if you decide to use maize, rice or sorghum? These starches gelatinise at higher temperatures: about 62°C to 72°C for maize and 68°C to 78°C for rice and sorghum. Unmalted, they also lack the enzyme activity that malting develops, and the heat needed to gelatinise their starch would destroy what little enzyme they carry. Using these grains with high gelatinisation temperatures requires a separate processing step, called grain cooking. It also requires an external source of enzymes (e.g. malted barley for Scotch grain whisky) to convert the starch. We will now examine the finer details of grain cooking.

Grain Cooking Process and Technology

The purpose of grain cooking is to gelatinise the starch of grains that did not go through a malting process.

We have already mentioned that efficient starch conversion requires starch to gelatinise first. The long starch chains must absorb water, and open to allow the enzymes to attack. A separate vessel is necessary for the cooking process. The figure below shows a typical grain cooker. The key components of this vessel are:

Grain cookerGrain cooker Mash out; Agitator / rake; Grain + water in; Steam in; Section view: flow paths and internal components are; simplified.UNDERSTANDING WHISKY PRODUCTIONGrain cookerMash outAgitator / rakeGrain + water inSteam inSection view: flow paths and internal components aresimplified.Uisge Beatha
Grain cooker

Cookers vary widely in capacity; at the large end, North British cooks 30 tonnes of grain every 90 minutes (scotchwhisky.com). The cooker commonly uses steam to heat the mash. At the start of the process, the steam flushes out the air before closing the vents; steam injection continues until the desired pressure is achieved. We should use only food grade chemicals with no carry over to produce the steam for direct injection. No impurities or substances that could cause harm to the consumer should be present.

Three factors can determine the effectiveness of the cooking process:

  1. The pressure reached, which will result in the correct temperature: saturated steam at about 150°C, for example, is at about 4 bar g (NIST steam data).
  2. The duration spent at the correct pressure.
  3. Water/grist ratio

The flow diagram below shows the cooking process for most grain cookers.

Cooking unmalted grainCooking unmalted grain. Schematic • not to scale. Mill the grain; Mix with water; Heat with steam; Hold for the required cooking time; Cool before adding malt or enzymes; Convert starch, then cool for; fermentationUNDERSTANDING WHISKY PRODUCTIONCooking unmalted grainMill the grainMix with waterHeat with steamHold for the required cooking timeCool before adding malt or enzymesConvert starch, then cool forfermentationUisge BeathaSchematic • not to scale
Cooking unmalted grain

Variations on this typical process can include milling the grains to flour and using water from the process to reduce water usage.

Backset is the thin watery liquid that remains after distillation; it also includes unfermented solids.

Backset is acidic; adding it to the grain cooker with the mash promotes the breakdown of the grains in the cooker. The acidity of the backset helps to bring the mash pH towards the range in which the malt enzymes work best (about 5.4 to 5.6 for β-amylase (Laus et al. 2025)).

The typical cooking process, as above, is a batch process. Batch cooking at atmospheric pressure is widely used in the production of whisky. Whereas grain neutral spirits use both batch and continuous cooking under pressure. Continuous cooking under pressure is a process where the mash is pumped through a cooker, exposing the mash to higher temperatures and pressures than batch cooking for a short time. Cooling of the cooked mash to conversion temperature occurs in a flash chamber, before mixing with a continuous stream of malt slurry. The mixture of cooked mash and malt slurry cools to fermentation temperature (about 15°C to 23°C for Scotch grain wort, per the Scotch Whisky Technical File) through a water-cooling system, before it enters the fermentation vessels. The continuous cooking process is more complicated; any delays during the process will waste energy or overcook the mash. The process needs to maintain a steady state in order to ensure efficiency.

Common factors to consider when using a continuous system include the following:

Both the batch and continuous cooking processes require the cooked grain to be cooled to a mash temperature of about 65°C before the malt goes in (Scotch Whisky Technical File), which if you recall suits barley malt α- and β-amylase. The distiller can now choose to add barley malt as a source of enzymes or exogenous enzymes, if permitted by local legislation. For Scotch whisky, regulation 3(1)(a)(ii) requires conversion to a fermentable substrate only by endogenous enzyme systems. If permitted, exogenous enzymes are a good substitution for malted barley, and perform better at higher temperatures. They are enzymes obtained from a different source, for example from fungi or bacteria.

Exogenous Enzymes

As we learned in the preceding section, working with unmalted cereals can present challenges. The primary issues are the gelatinisation and conversion of starch in mashes with low enzyme content. The previous section dealt with gelatinisation and conversion when malted barley is available. However, what happens at those times when there is no malt to add for conversion?

Some producers of grain neutral spirit are disinterested in using malted barley in any capacity, due to its added expense. In this case, exogenous enzymes will be used to break the starch molecules down into fermentable sugars. Let us look at the major enzymes used in the distilling industry.

The goal of starch conversion is to produce a fermentable wort, containing the nutrients that our yeast needs to convert sugar to alcohol. We can accomplish this in systems without barley malt enzymes by adding exogenous enzymes.

Exogenous enzymes are any enzymes that the distiller adds, i.e. they are not from the grains used in the mashing process. These enzymes are usually produced by bacteria or fungi, and then isolated and packaged in sanitised containers. Since these enzymes come from different sources, they behave slightly differently to the enzymes for barley malt. The effect they have on our grain starch is the same, but they will often be able to work at higher temperatures and within wider pH ranges.

Four main enzyme types are frequently used in the distilling industry. There are a handful of others, which are beyond the scope of this guide (due to the rarity of their use). The four main types are as follows:

  1. α-Amylases
  2. Amyloglucosidases
  3. Proteases
  4. Pullulanases

Amylases and amyloglucosidases are by far the most common enzymes used, so let us talk about these first.

Commercial α-amylase preparations work very similarly to their barley malt counterparts. Their primary function is liquefaction and to begin breaking down the larger starch polymers. Much like barley amylase, they tend to randomly clip starch polymers apart, reducing them in length and size. While this does produce a few fermentable sugars along the way, used by itself, this group of exogenous enzymes will not produce the most fermentable of worts in an unmalted cereal mash.

This is where the use of amyloglucosidase comes in. Sometimes referred to as glucoamylase, this enzyme does an excellent job of converting starch to fermentable sugars. It quickly breaks apart α-(1,4) bonds, forming many glucose molecules in the process. Amyloglucosidase also breaks α-(1,6) bonds, meaning that it can debranch amylopectin polymers. However, it does this at quite a slow rate.

Let us now discuss proteases. Used only occasionally, these enzymes catalyse reactions involving proteins. In this case, they break down proteins, specifically the protein matrix surrounding starch molecules. Remember that during the malting process, this is done for us by barley-derived proteases. However, we are talking about grains that have not undergone any malting. Therefore, they may still have a lot of protein surrounding the starch granules. This protein needs to be degraded before the starch granules can be gelatinised and undergo liquefaction.

The final exogenous enzymes that we will discuss are the pullulanases. These enzymes are called debranching enzymes because they specifically target α-(1,6) branch points in amylopectin. They are most commonly used in conjunction with other enzymes such as an amylase and amyloglucosidase preparation. While amyloglucosidase can also serve as a debranching enzyme, the pullulanases are usually much faster.

Key Takeaways

Mashing is a strict thermal balancing act. Strike water temperatures must be controlled within narrow margins: hot enough to gelatinise barley starch and activate amylase enzymes, but cool enough to avoid denaturing them before conversion is complete.

Sources and review

Cite this page

John Fegan (24 October 2026). "Milling and Mashing: Grist Proportions and Starch Conversion". Uisge Beatha. Updated 11 November 2026. https://uisgebeatha.co.uk/understanding-whisky-production/06-milling-and-mashing/. Accessed [date you read it].

Wikitext

<ref>{{cite web |title=Milling and Mashing: Grist Proportions and Starch Conversion |url=https://uisgebeatha.co.uk/understanding-whisky-production/06-milling-and-mashing/ |website=Uisge Beatha |author=John Fegan |date=24 October 2026 |access-date=[date you read it]}}</ref>

Where a point is covered by a paper, statute or official record named in the sources note, cite that first. Cite this page for its tables and worked explanations.

Want to test the whole course rather than one chapter? The whisky production quiz asks 12 questions from cereals and malting through to oak maturation.

About the author

John Fegan

· Editor

Hailing from the land of haggis and deep-fried Mars bars, John was always going to find his way to whisky. He has run Uisge Beatha since 2015 and Whiskipedia.com since 2020.